Hyundai Santa Cruz (NX4A OB) 2021-2025 Service Manual / Body Electrical System / Lighting System / Troubleshooting

Hyundai Santa Cruz: Lighting System / Troubleshooting

- Troubleshooting

Symptom	Possible cause	Remedy
One lamp does not light (all exterior)	Bulb burned out	Replace bulb
One lamp does not light (all exterior)	Socket, wiring or ground faulty	Repair if necessary
Head lamps do not light	Bulb burned out	Replace bulb
	Ignition fuse (LOW:10A, HIGH:20A) blown	Check for short and replace fuse
	Head lamp fuse (15A) blown	Check for short and replace fuse
	Head lamp relay faulty	Check relay
	Lighting switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Tail lamps and license plate lamps do not light	Bulb burned out	Replace bulb
	Tail lamp fuse (10A) blown	Check for short and replace fuse
	Tail lamp relay faulty	Check relay
	Lighting switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Stop lamps do not light	Bulb burned out	Replace bulb
	Stop lamp fuse (15A) blown	Check for short and replace fuse
	Stop lamp switch faulty	Adjust or replace switch
	Wiring or ground faulty	Repair if necessary
Stop lamps do not turn off	Stop lamp switch faulty	Repair or replace switch
Instrument lamps do not light (Tail lamps light)	Rheostat faulty	Check rheostat
Instrument lamps do not light (Tail lamps light)	Wiring or ground faulty	Repair if necessary
Turn signal lamp does not flash on one side	Bulb burned out	Replace bulb
	Turn signal switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Turn signal lamps do not light	Bulb burned out	Replace bulb
	Turn signal lamp fuse (10A) blown	Check for short and replace fuse
	Flasher unit faulty	Check flasher unit
	Turn signal switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Hazard warning lamps do not light	Bulb burned out	Replace bulb
	Hazard warning lamp fuse (15A) blown	Check for short and replace fuse
	Flasher unit faulty	Check flasher unit
	Hazard switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Flasher rate too slow or too fast	Lamps' wattages are smaller or larger than specified	Replace lamps
Flasher rate too slow or too fast	Flasher unit faulty	Check flasher unit
Back up lamps do not light	Bulb burned out	Replace bulb
	Back up lamp fuse (10A) blown	Check for short and replace fuse
	Back up lamp switch (M/T) faulty	Check switch
	Transaxle range switch (A/T) faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Room lamp does not light	Bulb burned out	Replace bulb
	Room lamp fuse (10A) blown	Check for short and replace fuse
	Room lamp switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Wiring or ground faulty	Repair if necessary
Map lamp does not light	Bulb burned out	Replace bulb
	Room lamp fuse (10A) blown	Check for short and replace fuse
	Map lamp switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary
Trunk room lamp does not light	Bulb burned out	Replace bulb
	Room lamp fuse (10A) blown	Check for short and replace fuse
	Trunk room lamp switch faulty	Check switch
	Wiring or ground faulty	Repair if necessary

Components and Components Location

- Component Location 1. Head lamp (Low & High)2. Head lamp (Low)3. Head lamp (High)4. Turn signal lamp5. Daytime running light (DRL) & Positioning lamp6. Side mark lamp7. Side repeater l ...

Specifications

- Specifications ItemsBulb TypeBulb Wattage (W) FrontHead lamp(STD)Low9005L+60 High9005L+60 Head lamp(Option)LowLEDLED HighLEDLED Turn signal lamp (STD)PY2828 Turn signal lamp (Option)LEDLED ...

Other information:

Hyundai Santa Cruz (NX4A OB) 2021-2025 Service Manual: Front Door Belt Inside Weatherstrip
- Replacement 1.Remove the front door trim.(Refer to Front Door - "Front Door Trim") 2.Remove the front door belt inside weatherstrip (A). 3.To install, reverse removal procedure. • When installing, install it by first contacting the inside part. ...

Hyundai Santa Cruz (NX4A OB) 2021-2025 Service Manual: Assist Handle
- Component Location 1. Assist handle - Replacement 1.After lifting up the assist handle caps and loosening the mounting screws, remove the assist handle (A). 2.To install, reverse removal procedure. ...